(2) Measure and if necessary, adjust the inboard cruise roller. (Ref. Fig. 406/TASK 27-54-62-991-013) (a) Measure the dimension Y: _ 1 _ 2 If the dimension Y is between zero and 2 mm (0.08 in.), the position of the cruise roller is correct. If the dimension Y is more than 2 mm (0.08 in.), you must adjust the inboard cruise roller.
(3) To adjust the inboard cruise roller: (a) Remove the nut (98), the collar (97) and the serrated plate (99). (b) Turn the eccentric (100) until the dimension Y is correct. (c) Install the serrated plate (99) to lock the eccentric (100). (d) Install the collar (97) and the nut (98). (e) TORQUE the nut (98) to between 2.4 and 2.7 m.daN (17.69 and 19.91 lbf.ft). (f) Do a check of the dimension Y again. (4) If the flap guide-roller assembly was removed, install it (Ref. TASK 27-54-63-400-001). R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499, Subtask 27-54-62-220-054 R. Measurement and Adjustment of the Flap Guide-Roller Assembly (Ref. Fig. 408/TASK 27-54-62-991-017) (1) Measure and if necessary, adjust the flap guide-roller assembly. (a) Measure the dimension D: _ 1 If the dimension D is more than 3 mm (0.12 in.), replace the flap guide-roller assembly with one of the correct size (Ref. TASK 27-54-63-400-001).
R
EFF : 001-049, 051-099, 101-149, 151-199, 201-299, 401-499, CES
27-54-62
Page 430 Aug 01/05
飞行翻译公司 www.aviation.cn 本文链接地址：A319 A320 A321 飞机维护手册 AMM Aircraft Maintenance Manual 18_部分11.pdf
(3) To adjust the inboard cruise roller: (a) Remove the nut (98), the collar (97) and the serrated plate (99). (b) Turn the eccentric (100) until the dimension Y is correct. (c) Install the serrated plate (99) to lock the eccentric (100). (d) Install the collar (97) and the nut (98). (e) TORQUE the nut (98) to between 2.4 and 2.7 m.daN (17.69 and 19.91 lbf.ft). (f) Do a check of the dimension Y again. (4) If the flap guide-roller assembly was removed, install it (Ref. TASK 27-54-63-400-001). R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499, Subtask 27-54-62-220-054 R. Measurement and Adjustment of the Flap Guide-Roller Assembly (Ref. Fig. 408/TASK 27-54-62-991-017) (1) Measure and if necessary, adjust the flap guide-roller assembly. (a) Measure the dimension D: _ 1 If the dimension D is more than 3 mm (0.12 in.), replace the flap guide-roller assembly with one of the correct size (Ref. TASK 27-54-63-400-001).
R
EFF : 001-049, 051-099, 101-149, 151-199, 201-299, 401-499, CES
27-54-62
Page 430 Aug 01/05
飞行翻译公司 www.aviation.cn 本文链接地址：A319 A320 A321 飞机维护手册 AMM Aircraft Maintenance Manual 18_部分11.pdf
自定义标签： 
